MFD export allows you to display the MFDs on a separate monitor.
- EECH has to run in full screen mode.
- Both monitors/adapters have to be configured in dualview mode e.g. set to Extend display across both monitors. Not in clone mode! If you click on Start->Control Panel->Display Properties->Settings->Identify both screens should show different numbers. (These numbers have nothing to do with the number in export_mfd_adapter=n. Here you have to try the numbers (0,1,2,3,...) until it works.)
- The defined MFD export screen resolution has to be supported by the export monitor
The best way to configure the screens
- set monitors in dualview mode e.g. set to Extend display across both monitors
- delete game.cfg
- run eech with mfdexport disabled
- configure the main screen in the game options menu
- quit EECH
- enable mfdexport and set mfd_export_adapter=0
- run EECH
If the game crashes (hangs or shows error message) then try mfd_export_adapter=1 (2,3,..)
MFD export should also work with different (mixed) graphic cards, e.g. the main screen is on one card and the MFDs on the other card. But both MFDs can only be displayed on the same card. It is not possible to put one mfd on one card and the second mfd on the other card.
How to render MFD on Android tablet using screen share VNC software
Example system: Windows 7 x64 PC with #1 FullHD monitor connected via DVI, which used for the main game rendering, and #2 1024x640 display using HDMI. They configured to be extended monitors, not cloned.
At this stage MFD data can be rendered on second display already, but in this example it will be used as dummy display for share target. Important to understand, that display will be turned off (in idle mode), but connected.
If you have no second monitor connected, you may try one of solution:
- if empty VGA port available, you can try to use it for adding fake display
- some software solution (like custom drivers) can be used but it may not work on some operation systems
- DIY plug for HDMI may force video adapter to add extra display, but you shouldn't do it without experience in electronics
First step is configure EECH.INI
export_mfd=1 # enable MFD export export_mfd_adapter=0 # 0 is connected display #2 export_mfd_screen_width=1024 # screen width export_mfd_screen_height=640 # screen height export_mfd_left_pos=0,0,512,512 # left MFD position: top left corner (0px, 0px) bottom right corner (512px, 512px), height same as with to preserve proportions export_mfd_right_pos=512,0,1024,512 # right MFD position: top left corner (512px, 0px) bottom right corner (1024px, 512px) export_mfd_single_pos=0,0,512,512 # no longer used
If possible, export can be tested using connected display after game launch.
Second step: configure share screen software.
RealVNC should be installed in Windows, it's only one known that have option to select target display. After installation, you can set up password and accept connections on default port (it can be changed if necessary). Then go to Expert tab and set DisplayDevice value as \\.\DISPLAY2 (number may differ). Ensure, that you have no antivirus or firewall software active, or at least whitelist selected port.
Enable Wi-Fi on Android device and install VNC Viewer application. Open it, create new connection using IP of your PC and selected port (default is 5900). You can enable View only mode as no need to capture controls. Connect to your PC - you will be asked to type password, and after that picture of secondary display will appear (black screen or current wallpaper).
Launch latest version of Enemy Engaged: Comanche vs. Hokum, shared screen should be black at this point. Start mission, get inside any helicopter, enable both MFDs and you will see their copy on the Android device screen.
One huge limitation of this method is high latency - it's 100-300ms and noticeable when you are using FLIR for DTV optics. You can try to decrease latency by making screen resolution smaller.
In similar way any other device can be used - Apple tablet, Windows laptop etc. that has VNC software installed.